Li-Ion Battery Charge Indicator YB27VE 60V 16 series

Description

Charge Indicator for Lithium Cells Series YB27VE 60V 16

This table can be set by pressing the battery type: lead-acid batteries, lithium batteries, nickel-metal hydride batteries, but also by pressing the button to set the number of batteries (batteries in series)
This meter is suitable for: car batteries from 12V, 24V, 36V, 48V, 60V, 72V, 84V, 96V, electric cars, battery packs, car balancing, inverters, electric lift trucks, tourist tours, electric cars, car batteries, mobile battery equipment, etc., can also be used for other voltages, load testing
This meter can be tested to show real-time voltage, power, and power percentage
Optional display mode: single voltage display; single power percentage display; voltage, power cycle percentage display (default setting)
Two-wire system, wide power supply voltage, wide test voltage range: DC6-120 V, wiring is simple and convenient
With reverse protection function, reverse does not burn out
Low power flash alarm function
LED color display, high-end atmosphere
Technical parameters:

Power supply voltage: DC6-120 V (wide range), Note: the maximum input voltage must not exceed 120 V, otherwise there is a risk of overheating
Test voltage: DC6 ~ 120 V (automatic decimal point movement)
Minimum resolution at 100 V or less: 0.1 V
Minimum resolution at 100 V or more: 1 V
Power resolution: 1%
Operating current: <20 mA
Display: color LED screen
Non waterproof section – YB27VE – Dimensions: 48 29 21 mm
Non waterproof – YB27VE – mounting hole: 45.5 26.5 mm
Measurement speed: 500mS / reading
Voltage measurement accuracy: 1%
Cable length: > 150mm

Extreme operating conditions:

Minimum supply voltage: +6V
Maximum supply voltage: + 120V
Operating temperature: -10 ~ +65°C
Operating humidity: 10 ~ 80% (no condensation)
Operating pressure: 80 ~ 106kPa
Sun exposure: no direct exposure

Tutorial: How to use the YB27VE 60V 16 series Charge Indicator

This charge indicator is ideal for monitoring the charge of 60V LiPo modules used in aircraft and vehicle models. Suitable for both beginners and intermediates.

What you need

• YB27VE 60V 16 series
• LiPo cells to monitor
• LiPo connector
• Multimeter (optional)

Steps

1. 1. Check the datasheet for your LiPo specifications.
2. 2. Prepare your LiPo and ensure the connector is clean.
3. 3. Connect the LiPo connector to the input port of the indicator.
4. 4. Check that the LED light is green, indicating full charge.
5. 5. Monitor the LED light to follow the charge level. Yellow = medium charge, red = low charge.
6. 6. Verify the voltage with the multimeter (optional).
7. 7. Turn off the load when the light turns red.
8. 8. Repeat the connection for additional LiPo modules.

Mini project

Build an automatic load for LiPo using the YB27VE indicator. Connect the indicator to a charging module and configure the Arduino to turn off the load when the light turns red.

Common mistakes

• Do not monitor the charge for too long with the multimeter, risking damage to the LiPo.
• Connect the LiPo only when the load is off.
• Do not use the indicator for loads above 60V.
• Do not forget to turn off the load when the light turns red.

Recommended accessories

• Arduino Nano
• Charging Module
• LiPo Connector
• Multimeter

Frequently asked questions

Can I use this indicator with a 3S LiPo?
Yes, but check the datasheet to ensure it is compatible with 12V.

How long does the indicator’s battery last?
Check the datasheet, but generally the battery lasts up to 1000 cycles.

Can I use the indicator for non-LiPo loads?
No, use the indicator only for LiPo elements.

Can I use the indicator for loads above 60V?
No, use the indicator only for LiPo elements up to 60V.