50MM Melting Furnace

50MM Melting Furnace

More details

ARD007966
New product

13,24 €

Currently available on order with delivery expected within 20 days from purchase.

- +

Free Google QRcode module

 
More info

50MM Melting Furnace

Precautions

Melting furnace must be placed on a stable, heat resistant work Taiwanese work, to prevent heat tin from tin pot spill. The molten tin and tin furnace temperature is higher overall, be careful work, beware of burns.
Tin stove during the initial use, please do not cause air burning tin pot tin oxide fast, please add small pieces of tin or tin part has been dissolved in order to ensure timely heat.
It must be placed separately and have solder furnace (including lead all items) to prevent lead contamination, so that there is no change Tin Tin, lead to product failure when lead-free melting furnace work. The company this serious statement, if such things happen, the company does not assume any responsibility.
Prohibit the use of melting furnace in the vicinity of flammable gases and flammable items.
When moving melting furnace must be cut off power supply when the furnace is cooled to room temperature and then proceeds.
This product is high temperature equipment, remember to turn off the power when not in use, to avoid accidents.
For safety and service life of tin stove, tin stove not more than 12 hours of continuous work.
For personal safety and machine to work properly, remember not air burning, used to take the "ground" of power use, while paying attention to "ground" unacceptable "zero line".
The company melting furnace furnace imported from Japan, refined titanium TAI materials, high temperature burning for a time after the tin pot pot surface becomes golden or blue, which is a normal phenomenon, but also the material properties of the metal.
The product quality assurance in all parts of the branded original accessories are used under the conditions, otherwise the quality is not guaranteed.
In the case of customer use, cook acids, bases, tin slag and other strong corrosive material, tin pot and the heating element will not warranty.
The furnace belongs not waterproof products, pay attention to moisture in use.
I. Overview:

 

   The company developed the CM series titanium-free solder furnace, has been through the authority of SGS environmental certification, is environmentally friendly lead-free, customers can be assured that the product tin pot Mining (preheat platform aluminum) pan using imported materials and titanium phase corresponding production technology; PID control with microcomputer chip, safe and reliable, stable performance, high precision, is the ideal tool for the production of the field of electronic wire industry indispensable.

 

Second, the performance characteristics:

 

   1, Cm-free solder furnace series of high-power heating core configuration, can quickly dissolve without Tin, from room temperature to reach 450 ℃, only 25 minutes or so (specific nuances will be based on the size of the furnace volume).

    2, microcomputer chip intelligent control, dual digital display, clear and intuitive, high thermal sensitivity, back to temperature quickly, fast temperature compensation.

    3, lead-free solder pot materials imported from titanium, high temperature, corrosion resistance, abrasion resistance and durability.

    4, the furnace is set directly input data using touch buttons, simple and accurate.

    5, set the machine data can be stored for long periods without shutdown, power failure affected.

 

Third, the working environment:

 

    1, the working voltage: AC220 ± 10V (can be customized 110V)

    2, Working temperature: 0--55 degree

    3, the working temperature: <90% RH non-condensing


Fourth, methods of operation and function setting:

 

   1, the temperature setting:

(1), open the furnace power switch, the operator panel displays temperature measurements 3.0.0 Temperature setpoint 2.8.0.0, directly plus + or minus - keys to adjust the temperature setpoint, press the plus + or minus - bond will rise or fall as a unit, long press the plus + or minus - keys to a continuous rise or fall, the value of the set temperature is automatically set after long-term storage in seconds, without switching machines, power outages affected.

(2), open the tin stove power, the operation panel displays temperature measurements 3.0.0 Temperature setpoint 2.8.0.0., Using the shift key type * to adjust the temperature setpoint, which figures behind the decimal point to stop in, you can Use of this number plus + or minus - keys to adjust. The set temperature is automatically set after long-term storage in seconds, without switching machines, outages.

 

    2, microcomputer auto-tuning:

  If the temperature measurements and temperature setpoint deviation too high (3-5 degrees), or temperature measurements and the actual oven temperature deviation is too high (10-20 degrees). Perform the auto-tuning operation, press and hold the shift key * three seconds the thermostat will automatically enter the self-tuning state, the display AT and the set temperature, and two subtitle will not stop cross flashing, direct 20 minutes -40 minutes Self-tuning at the end, only the normal display temperature you set. Self-tuning does not end when, if you want to quit and then press and hold the shift key * until the flashing stops can. The factory is to optimize the value of the parameter, generally do not auto-tuning.

 

    3, temperature compensation:

    If the temperature measurements and the actual oven temperature after self-tuning or deviation is too high, you can use the following method of correcting.

(1), hold down the CAL function key for two seconds to display the temperature measurements 5c temperature setpoint 0.0 at this time press + or - to compensate. Compensation is complete, press CAL function key twice to save and exit.

Example: Measured temperature value than the actual oven temperature by 10 degrees, with a minus - keys to adjust to the temperature measurements -10 5c temperature setpoint, then press the function key CAL save and exit. In contrast, the measured temperature value than the actual oven temperature by 10 degrees, with a plus + button to adjust to the temperature measurements 5c temperature setpoint 10, and then press the function key CAL save and exit.

(2) factory parameter values. Press and hold the CAL function key for two seconds, the display 5c 0.0, and then press the function key

CAL display Loc c, press the function key CAL, back to normal window, 5c that the compensation value.

Loc that the lock indicates unlocked.

 

    4 Note:

(1), self-tuning, the other parameters can not be adjusted. ,

(2), the self-tuning needs 20-40 minutes after the end of the auto-tuning process also requires a stable 10-20 minutes, during which time fluctuated temperatures are normal.


Five, fault detection

 

1, the boot is not energized, check the fuse is open, or the socket is plugged.

2, the boot display constant temperature, not heat up, showing off the heating element.

3, turned left display if the temperature is high, the right display HIA or ORA and has been blinking, open thermocouple, or temperature controller failure.

Write a review

50MM Melting Furnace

50MM Melting Furnace

Write a review

 
Comments(2)
03/20/2019
Feedback ricevuto nel nostro negozio eBay http://stores.ebay.it/domoticland

Fantastico, perfettamente funzionante!

  • Was this comment useful to you?
  • (0) (0)
01/24/2019
Feedback ricevuto nel nostro negozio eBay http://stores.ebay.it/domoticland

Ottimo

  • Was this comment useful to you?
  • (0) (0)

25 other products in the same category:

No products

To be determined Shipping
0,00 € Total

Check out